Technical Specifications
SPL
118 dB
Amplifier Power
250 W Bass (Class D) + 100 W Treble (Class D)
Frequency Response
36 Hz - 22 kHz ("-6 dB")
Accuracy of Frequency Response
± 2 dB (39 Hz - 19 kHz)
Driver Dimensions
⌀ 250 mm Bass + ⌀ 25 mm Treble (view in inches)
Dimensions
H 530 x W 360 x D 360 mm, with Iso-Pod™ (view in inches)
Weight
30 kg / 66.1 lb
Connections
1 x XLR Analog Input
1 x XLR AES/EBU Input
1 x XLR AES/EBU Output
2 x RJ45 Control
S360 SAM™ Studio Monitor
SAM™ Studio Monitor
Technical Specifications
The S360A delivers high SPL monitoring without compromising on predictability, speech intelligibility or sound quality.
System Specifications
Frequency Response
39 Hz - 19 kHz (± 2 dB)
Low cutoff -6dB
36 Hz
High cutoff -6dB
22 kHz
SPL
Peak SPL
≥128 dB
Maximum peak acoustic output per pair in a listening room with music material at 1 m.
Short term max SPL
≥118 dB
Maximum short term sine wave acoustic output on axis in half space, averaged from 100 Hz to 3 kHz at 1 m.
Long term max SPL
≥112 dB
Maximum long term RMS acoustic output in the same conditions with IEC weighted noise (limited by driver protection circuit) at 1 m.
Self-generated noise
Self-generated noise
≤10 dB SPL
Self generated noise level in free space at 1 m on axis (A-weighted).
Weight
Weight30 kg (66.1 lb)
Dimensions
Height
530 mm
(20 7/8 in)
Height with Iso-Pod
530 mm
(20 7/8 in)
Width
360 mm
(14 1/8 in)
Depth
360 mm
(14 1/8 in)
Enclosure
Enclosure material
MDF
Enclosure type
Reflex port
Drivers
Driver type
Cone
Diameter
250 mm
(9 7/8 in)
Driver type
Compression
Compression driver 44 mm (1.7 in) into a 25 mm (1 in) throat.
Diameter
25 mm
(1 in)
Directivity
Harmonic distortion
100 Hz...5 kHz ≤0.5 %
> 5 kHz ≤1.5 %
Group delay
The latency at high frequencies from the input to the acoustic output, measured in the analog input:
Extended Phase Linearity in GLM set to OFF
5.2 ms
In Genelec performance graphics, the time of converting the from an electronic input signal to the acoustic output in a Genelec monitor is described by two factors – latency and group delay. The group delay factor can be read in the graphics for a specific frequency. The total frequency-specific input-to-output delay is a sum of the latency and group delay factors. To understand the significance of this total delay, consider that moving a loudspeaker away by 1 meter creates an additional delay of about 3 ms.
Amplifier Section
Amplifiers
250 W Class D
100 W Class D
Mains voltage
100-240 VAC 50/60Hz
Power consumption
ISS Active
≤1 W
Idle
≤11 W
Full output
230 W
Signal processing section
Connectors
Input
Analog signal input connector XLR female, balanced 10 kOhm.
Input
Digital signal input connector XLR female 110 Ohm.
Output
Digital signal output / Thru connector XLR male 110 Ohm.
2 x Control
Two CAT5 (RJ45) GLM Network connectors for computer control using the Genelec Loudspeaker Manager (GLM) software.
